bf_original_balance_chassis/application/cmd/robot_cmd.c

// app
#include "robot_def.h"
#include "robot_cmd.h"
// module
#include "remote_control.h"
#include "ins_task.h"
#include "master_process.h"
#include "message_center.h"
#include "general_def.h"
#include "dji_motor.h"
#include "bmi088.h"
#include "user_lib.h"
#include "can_comm.h"
// bsp
#include "bsp_dwt.h"
#include "bsp_log.h"
// 私有宏,自动将编码器转换成角度值
#define PTICH_HORIZON_ANGLE (PITCH_HORIZON_ECD * ECD_ANGLE_COEF_DJI) // pitch水平时电机的角度,0-360

float yaw_align_angle = 0.0f, yaw_chassis_align_ecd = 2716;
static Publisher_t *chassis_cmd_pub;             // 底盘控制消息发布者
static Subscriber_t *chassis_feed_sub;           // 底盘反馈信息订阅者
static Chassis_Ctrl_Cmd_s chassis_cmd_send;      // 发送给底盘应用的信息,包括控制信息和UI绘制相关
static Chassis_Upload_Data_s chassis_fetch_data; // 从底盘应用接收的反馈信息信息,底盘功率枪口热量与底盘运动状态等

static RC_ctrl_t *rc_data;              // 遥控器数据,初始化时返回
static Vision_Recv_s *vision_recv_data; // 视觉接收数据指针,初始化时返回
static Vision_Send_s vision_send_data;  // 视觉发送数据

static Publisher_t *gimbal_cmd_pub;            // 云台控制消息发布者
static Subscriber_t *gimbal_feed_sub;          // 云台反馈信息订阅者
static Gimbal_Ctrl_Cmd_s gimbal_cmd_send;      // 传递给云台的控制信息
static Gimbal_Upload_Data_s gimbal_fetch_data; // 从云台获取的反馈信息

static Publisher_t *shoot_cmd_pub;           // 发射控制消息发布者
static Subscriber_t *shoot_feed_sub;         // 发射反馈信息订阅者
static Shoot_Ctrl_Cmd_s shoot_cmd_send;      // 传递给发射的控制信息
static Shoot_Upload_Data_s shoot_fetch_data; // 从发射获取的反馈信息

static Robot_Status_e robot_state; // 机器人整体工作状态

static Work_Mode_e vision_work_mode; // 视觉工作模式

static CANCommInstance *cmd_can_comm; // 底盘CAN通信实例
void RobotCMDInit()
{
    rc_data = RemoteControlInit(&huart3);   // 修改为对应串口,注意如果是自研板dbus协议串口需选用添加了反相器的那个
    vision_recv_data = VisionInit(&huart1); // 视觉通信串口

    gimbal_cmd_pub = PubRegister("gimbal_cmd", sizeof(Gimbal_Ctrl_Cmd_s));
    gimbal_feed_sub = SubRegister("gimbal_feed", sizeof(Gimbal_Upload_Data_s));
    shoot_cmd_pub = PubRegister("shoot_cmd", sizeof(Shoot_Ctrl_Cmd_s));
    shoot_feed_sub = SubRegister("shoot_feed", sizeof(Shoot_Upload_Data_s));

    CANComm_Init_Config_s comm_conf = {
        .can_config = {
            .can_handle = &hcan1,
            .tx_id = 0x312,
            .rx_id = 0x311,
        },
        .recv_data_len = sizeof(Chassis_Upload_Data_s),
        .send_data_len = sizeof(Chassis_Ctrl_Cmd_s),
    };
    cmd_can_comm = CANCommInit(&comm_conf);

    gimbal_cmd_send.pitch = 0;
    gimbal_cmd_send.yaw = 0;
    gimbal_cmd_send.gimbal_mode = GIMBAL_ZERO_FORCE;
    chassis_cmd_send.chassis_mode = CHASSIS_ZERO_FORCE;

    robot_state = ROBOT_STOP; // 启动时机器人进入工作模式,后续加入所有应用初始化完成之后再进入
}

/**
 * @brief 根据gimbal app传回的当前电机角度计算和零位的误差
 *        单圈绝对角度的范围是0~360,说明文档中有图示
 *
 */
static void CalcOffsetAngle()
{
    // 别名angle提高可读性,不然太长了不好看,虽然基本不会动这个函数
    static float angle;
    yaw_align_angle = yaw_chassis_align_ecd * ECD_ANGLE_COEF_DJI; // 从底盘获取的yaw电机对齐角度
    angle = gimbal_fetch_data.yaw_motor_single_round_angle;       // 从云台获取的当前yaw电机单圈角度
    if (yaw_chassis_align_ecd > 4096)                             // 如果大于180度
    {
        if (angle > yaw_align_angle)
            chassis_cmd_send.offset_angle = angle - yaw_align_angle;
        else if (angle <= yaw_align_angle && angle >= yaw_align_angle - 180.0f)
            chassis_cmd_send.offset_angle = angle - yaw_align_angle;
        else
            chassis_cmd_send.offset_angle = angle - yaw_align_angle + 360.0f;
    }
    else
    { // 小于180度
        if (angle > yaw_align_angle && angle <= 180.0f + yaw_align_angle)
            chassis_cmd_send.offset_angle = angle - yaw_align_angle;
        else if (angle > 180.0f + yaw_align_angle)
            chassis_cmd_send.offset_angle = angle - yaw_align_angle - 360.0f;
        else
            chassis_cmd_send.offset_angle = angle - yaw_align_angle;
    }
}

/**
 * @brief 控制输入为遥控器(调试时)的模式和控制量设置
 *
 */
static void RemoteControlSet()
{
    shoot_cmd_send.bullet_speed = 30;
    // // 云台参数,确定云台控制数据
    // if (switch_is_mid(rc_data[TEMP].rc.switch_left)) // 左侧开关状态为[中],视觉模式
    // {
    //     gimbal_cmd_send.yaw = ( vision_recv_data->yaw == 0 ? gimbal_cmd_send.yaw : vision_recv_data->yaw );
    //     gimbal_cmd_send.pitch =( vision_recv_data->pitch == 0 ? gimbal_cmd_send.pitch : vision_recv_data->pitch );
    // }
    // 左侧开关状态为[下],或视觉未识别到目标,纯遥控器拨杆控制
    chassis_cmd_send.vx = 0.0f;
    if (abs(rc_data[TEMP].rc.rocker_r1) > 300)
    {
        chassis_cmd_send.vx = 0.003f * (float)rc_data[TEMP].rc.rocker_r1; // _水平方向
        yaw_chassis_align_ecd = 2716;
    }
    else if (abs(rc_data[TEMP].rc.rocker_r_) > 300)
    {
        chassis_cmd_send.vx = 0.003f * (float)rc_data[TEMP].rc.rocker_r_; // _水平方向
        yaw_chassis_align_ecd = 765;
    }

    gimbal_cmd_send.yaw -= 0.001f * (float)rc_data[TEMP].rc.rocker_l_;
    gimbal_cmd_send.pitch -= 0.0004f * (float)rc_data[TEMP].rc.rocker_l1;
    // 摇杆控制的软件限位
    gimbal_cmd_send.pitch = float_constrain(gimbal_cmd_send.pitch, -35.0f, 30.0f);
    // gimbal_cmd_send.yaw = float_constrain(gimbal_cmd_send.yaw, -180.0f, 180.0f);

    // 底盘参数,目前没有加入小陀螺(调试似乎暂时没有必要),系数需要调整

    // 摩擦轮控制,拨轮向上打为负,向下为正
    if (rc_data[TEMP].rc.dial < -100) // 向上超过100,打开摩擦轮
        shoot_cmd_send.friction_mode = FRICTION_ON;
    else
        shoot_cmd_send.friction_mode = FRICTION_OFF;
    // 拨弹控制,遥控器固定为一种拨弹模式,可自行选择
    if (rc_data[TEMP].rc.dial < -400)
        shoot_cmd_send.load_mode = LOAD_BURSTFIRE;
    else
        shoot_cmd_send.load_mode = LOAD_STOP;
    // // 射频控制,固定每秒1发,后续可以根据左侧拨轮的值大小切换射频,
    // if( rc_data[TEMP].rc.switch_left == 3)
    // {
    //     shoot_cmd_send.friction_mode = FRICTION_ON;
    //     if(vision_recv_data->fire_mode ==AUTO_AIM)
    //         shoot_cmd_send.load_mode = LOAD_1_BULLET;
    //     else
    //         shoot_cmd_send.load_mode = LOAD_STOP;
    // }
    shoot_cmd_send.shoot_rate = 15;
}

/**
 * @brief 输入为键鼠时模式和控制量设置
 *
 */
static void MouseKeySet()
{
}

/**
 * @brief  紧急停止,包括遥控器左上侧拨轮打满/重要模块离线/双板通信失效等
 *         停止的阈值'300'待修改成合适的值,或改为开关控制.
 *
 * @todo   后续修改为遥控器离线则电机停止(关闭遥控器急停),通过给遥控器模块添加daemon实现
 *
 */
static void EmergencyHandler()
{

    if (switch_is_down(rc_data[TEMP].rc.switch_left) || switch_is_mid(rc_data[TEMP].rc.switch_left)) // 遥控器左侧开关状态为[下],遥控器控制
    {
        if (rc_data[TEMP].rc.dial > 300 || robot_state == ROBOT_STOP) // 还需添加重要应用和模块离线的判断
        {
            robot_state = ROBOT_STOP;
            gimbal_cmd_send.gimbal_mode = GIMBAL_ZERO_FORCE;
            chassis_cmd_send.chassis_mode = CHASSIS_ZERO_FORCE;
            shoot_cmd_send.shoot_mode = SHOOT_OFF;
            shoot_cmd_send.friction_mode = FRICTION_OFF;

            gimbal_cmd_send.yaw = gimbal_fetch_data.gimbal_imu_data.YawTotalAngle; // 急停时设定值保持与实际值同步，避免恢复时疯转
            gimbal_cmd_send.pitch = gimbal_fetch_data.gimbal_imu_data.Pitch;
        }
        // 遥控器右侧开关为[上],恢复正常运行
        if (switch_is_up(rc_data[TEMP].rc.switch_right))
        {
            robot_state = ROBOT_READY;
            shoot_cmd_send.shoot_mode = SHOOT_ON;
            gimbal_cmd_send.gimbal_mode = GIMBAL_GYRO_MODE;
            chassis_cmd_send.chassis_mode = CHASSIS_FOLLOW_GIMBAL_YAW;
        }
    }
    else if (switch_is_up(rc_data[TEMP].rc.switch_left)) // 遥控器左侧开关状态为[上],键盘控制
    {
        switch (rc_data[TEMP].key_count[KEY_PRESS_WITH_CTRL][Key_C] % 2) // ctrl+c 进入急停
        {
        case 0:
            robot_state = ROBOT_READY;
            shoot_cmd_send.shoot_mode = SHOOT_ON;
            break;

        default:
            robot_state = ROBOT_STOP;
            gimbal_cmd_send.gimbal_mode = GIMBAL_ZERO_FORCE;
            chassis_cmd_send.chassis_mode = CHASSIS_ZERO_FORCE;
            shoot_cmd_send.shoot_mode = SHOOT_OFF;
            shoot_cmd_send.friction_mode = FRICTION_OFF;
            shoot_cmd_send.load_mode = LOAD_STOP;

            gimbal_cmd_send.yaw = gimbal_fetch_data.gimbal_imu_data.YawTotalAngle; // 急停时设定值保持与实际值同步，避免恢复时疯转
            gimbal_cmd_send.pitch = gimbal_fetch_data.gimbal_imu_data.Pitch;
            break;
        }
    }
}
/* 机器人核心控制任务,200Hz频率运行(必须高于视觉发送频率) */
void RobotCMDTask()
{
    chassis_fetch_data = *(Chassis_Upload_Data_s *)CANCommGet(cmd_can_comm);

    SubGetMessage(shoot_feed_sub, &shoot_fetch_data);
    SubGetMessage(gimbal_feed_sub, &gimbal_fetch_data);

    // 根据gimbal的反馈值计算云台和底盘正方向的夹角,不需要传参,通过static私有变量完成
    CalcOffsetAngle();
    // 根据遥控器左侧开关,确定当前使用的控制模式为遥控器调试还是键鼠
    if (switch_is_down(rc_data[TEMP].rc.switch_left) || switch_is_mid(rc_data[TEMP].rc.switch_left)) // 遥控器左侧开关状态为[下],遥控器控制
        RemoteControlSet();
    if (switch_is_up(rc_data[TEMP].rc.switch_left)) // 遥控器左侧开关状态为[上],键盘控制
        MouseKeySet();

    EmergencyHandler(); // 处理模块离线和遥控器急停等紧急情况

    CANCommSend(cmd_can_comm, (void *)&chassis_cmd_send);

    PubPushMessage(shoot_cmd_pub, (void *)&shoot_cmd_send);
    PubPushMessage(gimbal_cmd_pub, (void *)&gimbal_cmd_send);
}