6020pitch driver

2026-10-24 01:52:20 +08:00 · 2026-03-17 19:44:51 +08:00
parent 0235c428c5
commit 31eef65a6d
6 changed files with 32 additions and 34 deletions
--- a/application/cmd/robot_cmd.c
+++ b/application/cmd/robot_cmd.c
@@ -207,6 +207,10 @@ static void RemoteControlSet()
        gimbal_cmd_send.pitch += 0.001f * (float)rc_data[TEMP].rc.rocker_l1;
    }
    // 云台软件限位
+    if (gimbal_cmd_send.pitch > PITCH_MAX_ANGLE)
+        gimbal_cmd_send.pitch = PITCH_MAX_ANGLE;
+    else if (gimbal_cmd_send.pitch < PITCH_MIN_ANGLE)
+        gimbal_cmd_send.pitch = PITCH_MIN_ANGLE;

    // 底盘参数,目前没有加入小陀螺(调试似乎暂时没有必要),系数需要调整
    chassis_cmd_send.vx = 0.15f * (float)rc_data[TEMP].rc.rocker_r_; // _水平方向
@@ -244,6 +248,12 @@ static void MouseKeySet()
    gimbal_cmd_send.yaw += (float)rc_data[TEMP].mouse.x / 660 * 10; // 系数待测
    gimbal_cmd_send.pitch += (float)rc_data[TEMP].mouse.y / 660 * 10;
    
+    // 云台软件限位
+    if (gimbal_cmd_send.pitch > PITCH_MAX_ANGLE)
+        gimbal_cmd_send.pitch = PITCH_MAX_ANGLE;
+    else if (gimbal_cmd_send.pitch < PITCH_MIN_ANGLE)
+        gimbal_cmd_send.pitch = PITCH_MIN_ANGLE;
+
    switch (rc_data[TEMP].key_count[KEY_PRESS][Key_Z] % 3) // Z键设置弹速
    {
    case 0:
--- a/application/gimbal/gimbal.c
+++ b/application/gimbal/gimbal.c
@@ -66,24 +66,20 @@ void GimbalInit()
    Motor_Init_Config_s pitch_config = {
        .can_init_config = {
            .can_handle = &hcan2,
-            .tx_id = 4,//2
+            .tx_id = 2,//2
        },
        .controller_param_init_config = {
            .angle_PID = {
-                .Kp = 10, // 10
+                .Kp = 40, // 10
                .Ki = 0,
                .Kd = 0,
-                .Improve = PID_Trapezoid_Intergral | PID_Integral_Limit | PID_Derivative_On_Measurement,
-                .IntegralLimit = 100,
-                .MaxOut = 500,
+                .MaxOut = 1000,
            },
            .speed_PID = {
-                .Kp = 50,  // 50
-                .Ki = 350, // 350
-                .Kd = 0,   // 0
-                .Improve = PID_Trapezoid_Intergral | PID_Integral_Limit | PID_Derivative_On_Measurement,
-                .IntegralLimit = 2500,
-                .MaxOut = 8000,//20000
+                .Kp = 80,  // 50
+                .Ki = 15, // 350
+                .Kd = 0.6,   // 0
+                .MaxOut = 30000,//20000
            },
            .other_angle_feedback_ptr = &gimba_IMU_data->Pitch,
            // 还需要增加角速度额外反馈指针,注意方向,ins_task.md中有c板的bodyframe坐标系说明
@@ -94,9 +90,11 @@ void GimbalInit()
            .speed_feedback_source = OTHER_FEED,
            .outer_loop_type = ANGLE_LOOP,
            .close_loop_type = SPEED_LOOP | ANGLE_LOOP,
+            // .outer_loop_type = SPEED_LOOP,//调试用
+            // .close_loop_type = SPEED_LOOP,
            .motor_reverse_flag = MOTOR_DIRECTION_NORMAL,
        },
-        .motor_type = DM4310,
+        .motor_type = GM6020,
    };
    // 电机对total_angle闭环,上电时为零,会保持静止,收到遥控器数据再动
    yaw_motor = DJIMotorInit(&yaw_config);
--- a/application/robot_def.h
+++ b/application/robot_def.h
@@ -29,8 +29,8 @@
 #define YAW_CHASSIS_ALIGN_ECD 1190  // 云台和底盘对齐指向相同方向时的电机编码器值,若对云台有机械改动需要修改
 #define YAW_ECD_GREATER_THAN_4096 0 // ALIGN_ECD值是否大于4096,是为1,否为0;用于计算云台偏转角度
 #define PITCH_HORIZON_ECD 3412      // 云台处于水平位置时编码器值,若对云台有机械改动需要修改
-#define PITCH_MAX_ANGLE 0           // 云台竖直方向最大角度 (注意反馈如果是陀螺仪，则填写陀螺仪的角度)
-#define PITCH_MIN_ANGLE 0           // 云台竖直方向最小角度 (注意反馈如果是陀螺仪，则填写陀螺仪的角度)
+#define PITCH_MAX_ANGLE 30           // 云台竖直方向最大角度 (注意反馈如果是陀螺仪，则填写陀螺仪的角度)
+#define PITCH_MIN_ANGLE -20           // 云台竖直方向最小角度 (注意反馈如果是陀螺仪，则填写陀螺仪的角度)
 // 底盘参数
 // #define CHASSIS_OMNI_WHEEL // 是否为全向轮底盘
 // #define CHASSIS_MCNAMEE_WHEEL     // 是否为麦克纳姆轮底盘
@@ -42,7 +42,7 @@
 #define STEERING_CHASSIS_ALIGN_ANGLE_LB STEERING_CHASSIS_ALIGN_ECD_LB / 8192.f * 360.f // 舵轮 D 对齐角度
 // 发射参数
 #define ONE_BULLET_DELTA_ANGLE 36    // 发射一发弹丸拨盘转动的距离,由机械设计图纸给出
-#define REDUCTION_RATIO_LOADER 49.0f // 拨盘电机的减速比,英雄需要修改为3508的19.0f
+#define REDUCTION_RATIO_LOADER 36.0f // 拨盘电机的减速比,英雄需要修改为3508的19.0f
 #define NUM_PER_CIRCLE 10            // 拨盘一圈的装载量
 // 机器人底盘修改的参数,单位为mm(毫米)
 #define WHEEL_BASE 350              // 纵向轴距(前进后退方向)
--- a/application/shoot/shoot.c
+++ b/application/shoot/shoot.c
@@ -52,10 +52,10 @@ void ShootInit()
            .motor_reverse_flag = MOTOR_DIRECTION_NORMAL,
        },
        .motor_type = M3508};
-    friction_config.can_init_config.tx_id = 1,
+    friction_config.can_init_config.tx_id = 3,
    friction_l = DJIMotorInit(&friction_config);

-    friction_config.can_init_config.tx_id = 2; // 右摩擦轮,改txid和方向就行
+    friction_config.can_init_config.tx_id = 4; // 右摩擦轮,改txid和方向就行
    friction_config.controller_setting_init_config.motor_reverse_flag = MOTOR_DIRECTION_REVERSE;
    friction_r = DJIMotorInit(&friction_config);

--- a/modules/algorithm/QuaternionEKF.c
+++ b/modules/algorithm/QuaternionEKF.c
@@ -199,8 +199,8 @@ void IMU_QuaternionEKF_Update(float gx, float gy, float gz, float ax, float ay,

    // 利用四元数反解欧拉角
    QEKF_INS.Yaw = atan2f(2.0f * (QEKF_INS.q[0] * QEKF_INS.q[3] + QEKF_INS.q[1] * QEKF_INS.q[2]), 2.0f * (QEKF_INS.q[0] * QEKF_INS.q[0] + QEKF_INS.q[1] * QEKF_INS.q[1]) - 1.0f) * 57.295779513f;
-    QEKF_INS.Pitch = atan2f(2.0f * (QEKF_INS.q[0] * QEKF_INS.q[1] + QEKF_INS.q[2] * QEKF_INS.q[3]), 2.0f * (QEKF_INS.q[0] * QEKF_INS.q[0] + QEKF_INS.q[3] * QEKF_INS.q[3]) - 1.0f) * 57.295779513f;
-    QEKF_INS.Roll = asinf(-2.0f * (QEKF_INS.q[1] * QEKF_INS.q[3] - QEKF_INS.q[0] * QEKF_INS.q[2])) * 57.295779513f;
+    QEKF_INS.Pitch = -asinf(-2.0f * (QEKF_INS.q[1] * QEKF_INS.q[3] - QEKF_INS.q[0] * QEKF_INS.q[2])) * 57.295779513f;
+    QEKF_INS.Roll = atan2f(2.0f * (QEKF_INS.q[0] * QEKF_INS.q[1] + QEKF_INS.q[2] * QEKF_INS.q[3]), 2.0f * (QEKF_INS.q[0] * QEKF_INS.q[0] + QEKF_INS.q[3] * QEKF_INS.q[3]) - 1.0f) * 57.295779513f;

    // get Yaw total, yaw数据可能会超过360,处理一下方便其他功能使用(如小陀螺)
    if (QEKF_INS.Yaw - QEKF_INS.YawAngleLast > 180.0f)
--- a/modules/motor/DJImotor/dji_motor.c
+++ b/modules/motor/DJImotor/dji_motor.c
@@ -24,7 +24,7 @@ static CANInstance sender_assignment[6] = {
    [1] = {.can_handle = &hcan1, .txconf.StdId = 0x200, .txconf.IDE = CAN_ID_STD, .txconf.RTR = CAN_RTR_DATA, .txconf.DLC = 0x08, .tx_buff = {0}},
    [2] = {.can_handle = &hcan1, .txconf.StdId = 0x2ff, .txconf.IDE = CAN_ID_STD, .txconf.RTR = CAN_RTR_DATA, .txconf.DLC = 0x08, .tx_buff = {0}},
    [3] = {.can_handle = &hcan2, .txconf.StdId = 0x1ff, .txconf.IDE = CAN_ID_STD, .txconf.RTR = CAN_RTR_DATA, .txconf.DLC = 0x08, .tx_buff = {0}},
-    [4] = {.can_handle = &hcan2, .txconf.StdId = 0x3FE, .txconf.IDE = CAN_ID_STD, .txconf.RTR = CAN_RTR_DATA, .txconf.DLC = 0x08, .tx_buff = {0}},
+    [4] = {.can_handle = &hcan2, .txconf.StdId = 0x200, .txconf.IDE = CAN_ID_STD, .txconf.RTR = CAN_RTR_DATA, .txconf.DLC = 0x08, .tx_buff = {0}},
    [5] = {.can_handle = &hcan2, .txconf.StdId = 0x2ff, .txconf.IDE = CAN_ID_STD, .txconf.RTR = CAN_RTR_DATA, .txconf.DLC = 0x08, .tx_buff = {0}},
 };

@@ -321,25 +321,15 @@ void DJIMotorControl()
        // 获取最终输出
        set = (int16_t)pid_ref;

-
        // 分组填入发送数据
        group = motor->sender_group;
        num = motor->message_num;
-
-        if (i == 1)
-        {
-            sender_assignment[4].tx_buff[6] = (uint8_t)(set & 0x00ff); // 高八位
-            sender_assignment[4].tx_buff[7] = (uint8_t)(set >> 8); // 低八位
-        }
-        else
-        {
        sender_assignment[group].tx_buff[2 * num] = (uint8_t)(set >> 8);         // 低八位
        sender_assignment[group].tx_buff[2 * num + 1] = (uint8_t)(set & 0x00ff); // 高八位
-        }

        // 若该电机处于停止状态,直接将buff置零
        if (motor->stop_flag == MOTOR_STOP)
-            memset(sender_assignment[group].tx_buff + 2 * num, 0, 2u);
+            memset(sender_assignment[group].tx_buff + 2 * num, 0, sizeof(uint16_t));
    }

    // 遍历flag,检查是否要发送这一帧报文